After adding legacy support it now sticks to a 7.Īsus Rampage II Extreme, Chipset Intel X58 Modded Bios and Meltdown/Spectre Microcode patchġx NVME 500GB Samsung 950 Pro M2 SSD with cheap PCI Express adapter 4 lanes 2.0 Is there any chance to use Clover from USB Stick to boot my existing Samsung 950 Pro WHILE RAID keeps active in BIOS and these SSDs are connected? It is stuck to black screen with only a 6. I don´t wanna miss my semi hardware BIOS Raid. When I switch to AHCI the Raid dissapears and also everything boots up. When I just unplug these i can boot Win 10 directly from Samsung 950 Pro via NVME/Pcie adapter while NO other RAID1 SSDs are connected (BIOS MODE is stil: RAID). I cannot enable built-in Intel SATA RAID on my Rampage II or the BIOS fails to recognize my 950 Pro is bootable while my RAID1 SSDs are connected. After you run the diskpart script you can select the location for windows iso and click setup at the bottom right. This allows you to format for bios or uefi boot. You need to right click on the top bar to run a diskpart script first. I usually boot with sergei strelec’s winpe and then use WinNTSetup to install whatever version of windows i want to the drive. If you just install it in bios mode it will not boot properly when you try and use clover. I’ve found opencore works the best.Īlso, the reason the guide has you boot the installation media with clover is that it puts it into efi mode, which will allow it to boot properly when it is installed. Now you have a very versatile usb stick that should be able to run uefi with at least one of them. Lastly, I’d copy refindplus to \EFI\Boot\boot圆4.efi Use this menu.lst file so you can choose between 3 different uefi emulatorsĬhainloader -force -load-segment=0x2000 -load-offset=0x200 -boot-cs=0x2000 -boot-ip=0x200 /boot圆4Ĭhainloader -force -load-segment=0x2000 -load-offset=0x200 -boot-cs=0x2000 -boot-ip=0x200 /boot7Ĭhainloader -force -load-segment=0x2000 -load-offset=0x0 -boot-cs=0x2000 -boot-ip=0x200 /efildr20 I’d wipe that usb stick and format it with ntfs then make it grub4dos 0.4.6a bootable using bootice. Well, I’ve found the bootloaders for just about all the uefi emulators have pretty bad compatibility in general. I appreciate any thanks to your batch download, i finally got clover to boot, at least on my asus m4a88td-v evo/usb3.Īt the moment clover does not finish loading or recognizing the hardware on my acer aspire 5630 BL50, it stays blockedįor now I will continue reading, learning in this fantastic forum and you all for making this possible. Do you have any suggestion? Has anyone modified the BIOS of this laptop successfully? I tried to create a bootable USB with BDU, installing Clover EFI bootloader, I followed the guide on the forum, but Clover doesn’t detect my NVMe drive. On the other hand, the W-10 installation USB recognizes the NVMe and manages to install W-10 even though it is impossible to boot. However, W-10 does recognize it as a data disk and gave speeds of up to 100 Mb/s. So, I removed the WIFI miniPCIe card and installed a NVMe PCIe M2 SSD using an adapter to mPCIe. I installed a SATA SSD and curiously either it did not recognize it (kingston A400), it recognized it and could not work with it (if it was a TB) or after recognizing it and installing W-10 it worked even slower than the SATA HDD or the IDE HDD. I improve but almost negligibly (Speeds between 7 and 12 Kb/s). Regarding the Acer Aspire 5630 BL50 laptop: To try to speed it up I tried to put a 500 Gb SATA HDD through an IDE port adapter. Is there a possibility to modify the BIOS on either of these two motherboards? Do you use OpRomCfg in MS2 environment or in windows? to me in windows 10 a window opens and closes in tenths of a second. If you have any suggestions, material or help, I would greatly appreciate it. However, with a SATA III 6 Gb/s Kingston A400 SSD they seem to work with decent speed, and for now I think I’m going to settle, not give up. On the other hand, W-10 installed on another drive detects it and is able to work with it as a data drive which is not an advantage. However, although the windows 10 installation USB detects it, it is unable to install the operating system. I have created a bootable USB with BDU, installing Clover EFI bootloader, as you explain in the forum, but clover does not detect the disk. On both motherboards I have tried to install a NVMe M2 SSD using a PCIe adapter. Let me explain: I have a GA-890GPA-UD3H motherboard Another Asus M4A88TD-V EVO/USB3 and an Acer Aspire 5630 BL50 laptop I have a Museum of the Paleozoic of Hardware.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |